Category 2 · Materials Processing · A · Systems, Equipment and Components
ECCN 2A999
Specific Processing Equipment, n.e.s., as Follows (See List of Items Controlled).
Reason for Control
AT
Control(s) · Country Chart column
No control table in this entry (see the entry text).
Control(s):
Country Chart. AT applies to entire entry. A license is required for items controlled by this entry to North Korea for anti-terrorism reasons. The Commerce Country Chart is not designed to determine AT licensing requirements for this entry. See § 742.19 of the EAR for additional information.
List Based License Exceptions (as published)
- LVS: N/A
- GBS: N/A
List of Items Controlled
Related Controls: See also 2A226, 2B350.
Related Definitions: N/A
Items (2 lines)
a. Bellows sealed valves;
b. Reserved.
Technical Notes for 2B001 to 2B009, 2B201, and 2B991 to 2B999: 1. Secondary parallel contouring axes, (e.g., the w-axis on horizontal boring mills or a secondary rotary axis the center line of which is parallel to the primary rotary axis) are not counted in the total number of contouring axes. Rotary axes need not rotate over 360°. A rotary axis can be driven by a linear device (e.g., a screw or a rack-and-pinion). 2. The number of axes which can be coordinated simultaneously for “contouring control” is the number of axes along or around which, during processing of the workpiece, simultaneous and interrelated motions are performed between the workpiece and a tool. This does not include any additional axes along or around which other relative motions within the machine are performed, such as: 2.a. Wheel-dressing systems in grinding machines; 2.b. Parallel rotary axes designed for mounting of separate workpieces; 2.c. Co-linear rotary axes designed for manipulating the same workpiece by holding it in a chuck from different ends. 3. Axis nomenclature shall be in accordance with International Standard ISO 841:2001, Industrial automation systems and integration—Numerical control of machines—Coordinate system and motion nomenclature. 4. A “tilting spindle” is counted as a rotary axis. 5. 'Stated “unidirectional positioning repeatability” ' may be used for each specific machine model as an alternative to individual machine tests, and is determined as follows: 5.a. Select five machines of a model to be evaluated; 5.b. Measure the linear axis repeatability (R↑,R↓) according to ISO 230-2:2014 and evaluate “unidirectional positioning repeatability” for each axis of each of the five machines; 5.c. Determine the arithmetic mean value of the ”unidirectional positioning repeatability”-values for each axis of all five machines together. These arithmetic mean values “unidirectional positioning repeatability” (UPR) become the stated value of each axis for the model...) (UPRX, UPRy, . . .); 5.d. Since the Category 2 list refers to each linear axis there will be as many 'stated “unidirectional positioning repeatability” ' values as there are linear axes; 5.e. If any axis of a machine model not controlled by 2B001.a. to 2B001.c. has a 'stated “unidirectional positioning repeatability” ' equal to or less than the specified “unidirectional positioning repeatability” of each machine tool model plus 0.7 µm, the builder should be required to reaffirm the accuracy level once every eighteen months. 6. For the purpose of 2B, measurement uncertainty for the “unidirectional positioning repeatability” of machine tools, as defined in the International Standard ISO 230-2:2014, shall not be considered. 7. For the purpose of 2B, the measurement of axes shall be made according to test procedures in 5.3.2. of ISO 230-2:2014. Tests for axes longer than 2 meters shall be made over 2 m segments. Axes longer than 4 m require multiple tests (e.g., two tests for axes longer than 4 m and up to 8 m, three tests for axes longer than 8 m and up to 12 m), each over 2 m segments and distributed in equal intervals over the axis length. Test segments are equally spaced along the full axis length, with any excess length equally divided at the beginning, in between, and at the end of the test segments. The smallest “unidirectional positioning repeatability”-value of all test segments is to be reported.
Country Chart row viewer
Shows the X marks in the columns this entry cites (Supplement No. 1 to Part 738) for one destination. It does not state a license conclusion.
Loading…
Source: https://www.ecfr.gov/api/versioner/v1/full/2026-11-09/title-15.xml?part=774. eCFR issue date 2026-11-09; last checked for a newer eCFR issue 2026-11-16. The eCFR is not the official legal edition of the CFR. Official tools: BIS Interactive CCL · SNAP-R (CCATS) · eCFR Supplement No. 1 to Part 774. Classification of your product is not provided here — see SNAP-R / CCATS.